Showing results: 46 - 60 of 76 items found.
-
ATS1800C -
Rohde & Schwarz GmbH & Co. KG
The R&S®ATS1800C CATR based 5G NR mmWave test chamber provides the ideal environment for testing 5G FR2 antennas, modules and devices over the air (OTA) from R&D to conformance. With its small footprint and wide frequency range, the R&S®ATS1800C offers great functionality and test coverage in a very small space. With its flexibility and broad range of extension options, the R&S®ATS1800C offers a solid and future-proof environment for your FR2 testing needs.
-
Eastern-Optx
Operating from 20 to 40 GHz, two radios may be connected to the system allowing full duplex operation. Each radio may operates over identical Air Interface with uni or bi-directional multipath. The delays between radios may be varied from 0 to 1 mile in 5 foot steps with propagation loss control. The 2040+ creates a variable test range right in your lab. It can be used as a design aid and as a test tool for new modulation and encryption schemes prior to expensive and time consuming field testing.
-
MilliBox Original
If you are involved in antenna or system level design using mmWave or THz frequencies, then you understand the importance of dependable testing equipment. It may be that you are designing passive phase array or that you are designing a mmWave radar sensor system, but when it comes to validation of your design, simulation can only bring you so far. Phased array antennas have to be measured over the air (OTA) to ensure the radiation pattern of your design efficiently conducts energy in the right direction which is where the MilliBox comes in.
-
ATS800R -
Rohde & Schwarz GmbH & Co. KG
The R&S®ATS800R CATR based 5G NR mmWave test chamber provides a very compact over the air (OTA) testing environment for testing 5G FR2 antennas, modules and devices in R&D. The R&S®ATS800R has a very small footprint and wide frequency range, and offers maximum functionality and test coverage in a small space. The flexible setup options and range of extensions make the R&S®ATS800R a solid and future-proof environment for your FR2 testing needs.
-
JSECST™ -
Textron Systems
The Joint Services Electronic Combat Systems Tester (JSECST) is part of the family of testers, supporting the U.S. Air Force, Navy, Army, and over 23 allied nation platforms. JSECST performs full end-to-end diagnostic tests of installed systems including radar warning receivers (RWRs), jamming systems, communication systems, and navigation systems. Our JSECST delivers confidence for flight crews and the technicians who support them. It quickly and accurately tests and fault-isolates electronic combat and avionics systems for today's most advanced combat aircraft.
-
GAO Tek Inc.
GAOTek’s environmental testers can be used to measure parameters such as humidity, temperature, wind speed or velocity, wind direction, air quality, electromagnetic waves, ionizing radiation and more. Environmental testers are applicable in climate monitoring to occupational health and safety (OHS) applications. Our environmental testers are useful tools for collecting data about the immediate surroundings. Depending on the model, an environmental tester can function as a data logger for long-term data by collecting and storing measurement data over a certain period. Our environmental test solutions are affordable and dependable and are perfect for general to specialized jobs.
-
Cincinnati Sub-Zero Products
We provide a large selection of thermal shock chambers to accommodate various types of product testing. Thermal Shock Chambers perform tailored environmental stress screening of component and board electronic assemblies. Our unique chamber design transfers product between two extreme temperature-controlled chambers, passing equal volumes of high velocity conditioned air over the product and resulting in rapid product temperature changes. The induced thermal stresses can reveal hidden manufacturing defects in electronic sub-assemblies and other components by the expansion and contraction of critical parts.
-
FW Series -
Bemco Inc.
The Bemco FW Series of mechanically cooled Glass Door Humidity Chambers have a a temperature range of -28 C to +177 C (-20 F to 350 F) or -73 C to +177 C (-100 F to 350 F) and a humidity range of up to 5% RH to 95% RH.. These chambers feature direct dry air injection and direct humidity sensors. They operate without dewpoint limit from 5% RH to 95% RH over the range of 30 C to 85 C and even allow operation at 20% RH at 5 C and 50% RH at -14 C!
-
B-1002 -
Ruetz Technologies GmbH
Ross High Current Switches are available up to 36,000 amps continuous and over 1,700,000 amps 20µsec RC pulse, with voltage ratings of 6 volts to 400kV peak test. Standard Ross high current switches are built with 80 to 120psi air cylinder actuators. Air cylinder or motor operated for high contact force. Arcing contacts optional for closing current. G-10 epoxy glass laminate is standard insulation on most models. G-7 silicone glass is used on models available for RF applications above 100kHz. Most Ross high current switches are available with additional lengths of insulation, where the high voltage contacts need to be spaced at a greater distance from the actuator and control circuit. Voltage withstand value is at least doubled and the interrupt capability is much greater when high current switches are immersed in insulating oil, fluid or SF6 gas. For gas atmosphere, no modifications are necessary; however, oil or fluid immersion requires modification at a slight extra cost.
-
B-1002 -
ROSS ENGINEERING CORPORATION
Ross High Current Switches are available up to 36,000 amps continuous and over 1,700,000 amps 20µsec RC pulse, with voltage ratings of 6 volts to 400kV peak test. Standard Ross high current switches are built with 80 to 120psi air cylinder actuators. Air cylinder or motor operated for high contact force. Arcing contacts optional for closing current. G-10 epoxy glass laminate is standard insulation on most models. G-7 silicone glass is used on models available for RF applications above 100kHz. Most Ross high current switches are available with additional lengths of insulation, where the high voltage contacts need to be spaced at a greater distance from the actuator and control circuit. Voltage withstand value is at least doubled and the interrupt capability is much greater when high current switches are immersed in insulating oil, fluid or SF6 gas. For gas atmosphere, no modifications are necessary; however, oil or fluid immersion requires modification at a slight extra cost.
-
Vivaldi -
DVTest Inc.
The dbDIRECT Broadband Antenna features a broad frequency range of operation, high gain, small form factor and directional radiation pattern, making it highly attractive for widespread use in test and measurement of emerging wireless technology devices and radars. Contrary to conventional Vivaldi antennas limited to operating only at higher frequencies, the dbDIRECT Broadband Antenna design is optimized to operate at a frequency as low as 700 MHz up to 6 GHz. This lightweight and compact antenna design provides excellent matching over a broad frequency range.The antenna is designed to be placed in a DVTEST's portable anechoic chamber such as the dbSAFE enclosures for OTA (Over the Air) testing of DUTs. The antennas can be mounted in fixed positions to facilitate repeatable results. When used in conjunction with a rotary positioning mechanism, customers are able to detect the highest point of power sensitivity for enhanced accuracy and repeatability in measurements. In this configuration, both the antennas and DUTs can be positioned in order to facilitate the measurement.
-
1000D -
Dimax
CoolMaster 1000D is versatile bridge device connecting Daikin VRV Air Conditioning systems and any RS232 or USB capable device like Home PC, Embedded PC or Home Automation Controller. Exposing simple interface over RS232 communication line or USB bus, CoolMaster gains user application full control on indoor units and provides access to VRV system parameters. In other words CoolMaster hides complexity of internal Daikin Communication line (including very unique physical layer) and instead gives simple, comprehensive, well documented protocol running on popular RS232 or USB connection.
-
SHF Communication Technologies AG
SHF’s microwave components are broadband devices suitable up to 110 GHz. Our SHF BIAS TEES are well known but perhaps a slight variation does suit your application even better. DIPLEXERS are bias tees with a certain bandwidth in the low frequency path to combine or separate high frequency and low frequency signals into or out of a single line. DC-FEEDERS are bias tees without the capacitor. Therefore, it provides slightly lower insertion loss in case it is connected to an AC-coupled device which already has a capacitor on its input. Based on our air line construction, these passive components provide resonance-free transmission over the entire operating range.
-
Darwin Chambers Company
Darwin Chambers Company ALAAC, OLAW, USDA, and NIH-compliant Vivarium Rooms are designed for maximum value, sustainability, and conformance with applicable standards. We have over a decade of experience in working with researchers to provide humane and often precise conditions to meet their unique and specific needs. Vivariums are commonly defined as a place, such as a in laboratory, where live animals and/or plants are kept under conditions simulating a natural environment. Often, these contain both plants and animals, within a micro-ecosystem, often with controlled stability or controlled change of environmental variables. We offer various surface finishes, including all stainless steel, which are easy to maintain and may be sterilized to cleanroom standards. Compartmentalized enlosures are offered, which are modular and reconfigurable. Our rooms will accommodate plants as needed (we also provide plant growth chambers), and we offer control of humidification in conformance with current ALAAC mandates, sufficient air exchanges, available HEPA filtration of intake and/or exhaust air, standard screened equipment hous- ings, and other such considerations.
-
Aero Nav Laboratories, Inc.
This test determines the effects of direct solar radiation on components and material. The heating effects of solar radiation differ from those of high air temperature in that the amount of heat absorbed depends on the roughness and color of the surface on which the radiation is incident and the angle of incidence to the sun. Variations in the intensity of solar radiation over the surface of the component, may cause components to expand or contract at different rates, which can lead to severe stresses and loss of structural integrity. In addition, degradation due to photo-chemical changes can occur such as fading of color, deterioration of natural and synthetic elastomers and polymers. The test items that are subjected to solar radiation testing are those that are exposed to solar radiation during its life cycle, in the open, in warm climates.